Access Keys:
Skip to content (Access Key - 0)

Welcome to the OpenRemote Community

Discuss OpenRemote with us on the Mailinglist (or browse Forums archive).

You can find source code on SourceForge and Github.

Contact us for commercial support & service solutions.

Recent Contributions

v2.5 designer Switch only taking command for the off position
HI any one run in to an issue where a Switch for Zwave only works in one direction i.e. OR2.5 seems to execute command only for the OFF position- in other words when i press the switch button from the app, it will only execute the command assigned to the switch off position. i have attached
Re: SONY TV
Hey - can't help you with those errors sorry, but I followed this post to control my Sony from OR running on a pie: http://www.openremote.org/display/forums/Sony+TV+Control+IP+%28alternative%29 Below is a run down of what I've done: http://jesifren.blogspot.com.au/2016/05/sony-tv-ip-control.htm
Re: Controller 2.5 and KNX DPT:s
Hi. I noticed the same thing. I have always used a controller version from Juha's workspace called "Controller_2_1_0_FM_KNXRollback" I think it is the last KNX version he did. It is the most complete and bug fixed KNX code (according to me). It's too bad that it was never released. I have
Controller 2.5 and KNX DPT:s
Hello I'm coming from controller 2.1 and after trying 2.5 I noticed that some KNX DPTs doesn't are not recognized any more(10.001 time, 11.001 date, 13.001 counter pulses etc...). Also DPT 16.000 isn't recognized although it is mentioned there: http://www.openremote.org/display/docs/OpenRemote+
Fresh raspberrypi
Hi, I,m fiddling around to get my fresh installed raspberrypi controller with v2.6 syncd and running. The controller says but in the designer the controller is not found Some error from the console: ERROR 2016-07-19 10:51:16,149 : Creating sensor failed. Error : No device protocol builders
Help to install OR on Synology
I have been running OR for quite some time on my Synology 412+. Up until now I have used the pcloadletter package to install OR. However after updating from version DSM 5.x to DSM 6 (Synology software) the pcloadletter package is no useable. I know many here is running OR on a Synology, but have
Re: Zwave- node battery status
A battery powered device is most of the times in sleep mode and as a result it's not possible to communicate with the device and request the battery status update. In order to communicate with the device the controller waits for a wake up command from the device and sends all commands that have
Re: ZWave Dim to fixed value
I've verified that the Z-Wave 'DIM' command with a fixed value like 'DIM 50' works with OpenRemote Controller 2.5.0. (New release for OpenRemote : https://t.co/HnlA81iJrV, https://t.co/aRW3jBoneG)
Re: EnOcean
Some more info in the log, not sure why it is shutting down. DEBUG 2016-07-17 12:59:59,833 (EnOcean): Adding shutdown hook to manage unclosed EnOcean connections in case of controller exit. DEBUG 2016-07-17 13:00:00,229 (EnOcean): Try to read EnOcean module base ID (retry count = 1) INFO
Re: OpenRemote Re: Help knx
Could you try and use a different computer instead the pi? On 15.07.2016, at 12:20, Gianluca Pascarella wrote: Hallo, I've tryed to reset my interface from ets but nothing changed. I can't get the status. I don't know what else I can do. Any help is appreciated Il
© 2016 OpenRemote Inc. All Rights Reserved.
Adaptavist Theme Builder (3.3.6-conf210) Powered by Atlassian Confluence 2.10.3, the Enterprise Wiki.